child restraint MITSUBISHI CARISMA 2000 1.G Owners Manual

Seats and Seatbelts
Seat adjustment 3–2. . . . . . . . . . . . . . . . . . . . . . . . . .
Rear seat 3–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Head restraints 3–7. . . . . . . . . . . . . . . . . . . . . . . . . . .
Armrest* 3–9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heated seats* 3–10. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seat belts 3–11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Child restraint 3–15. . . . . . . . . . . . . . . . . . . . . . . . . . .
Pregnant women restraint 3–21. . . . . . . . . . . . . . . . .
Seat belt inspection 3–21. . . . . . . . . . . . . . . . . . . . . .
Supplemental restraint system (SRS) - air
bag 3–22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SEATS AND SEATBELTS
3–2
Seat adjustmentEG21A-Ud
Adjust the driver’s seat so that you are com-
fortable and that you can reach the pedals,
steering wheel, switches etc. while retaining
a clear field of vision.
WARNING
(1) If required, always adjust the
seating before the vehicle is in
motion. After adjustments are
made, ensure the seating is
locked in position by attempting
to move the seat and seatback
forward and rearward without
using the adjusting mechanism.
WARNING
(2) It is extremely dangerous to ride
in the luggage area (inside or out-
side) of a vehicle. Also, the lug-
gage area and rear seats should
never be used as a play area by
children. In a collision, people or
children riding unrestrained in
these areas are more likely to be
seriously injured or killed.
Do not allow people or children to
ride in any area of your vehicle
that is not equipped with seats
and seat belts, and make sure
that everyone travelling in your
vehicle is in a seat and wearing a
seat belt, or in the case of a child
is strapped in a child restraint.
In the interest of their safety,
children should not be allowed to
adjust the seats.
WARNING
(3) To minimize the risk of personal in-
jury in the event of a collision or
sudden braking, the seatbacks
should always be in the almost up-
right position while the vehicle is in
motion. The protection provided
by the seat belts may be reduced
significantly when the seatback
is reclined. There is greater risk
that the passenger will slide
under the seat belt, resulting in
serious injury, when the seatback
is reclined.

SEATS AND SEATBELTS
3–3
CAUTION
(1) Make sure that the seat is ad-
justed by an adult.
If it is adjusted by a child, an unex-
pected accident might occur.
(2) Do not place a cushion or the like
between your back and the seat-
back while driving. The effective-
ness of the head restraints will be
reduced in the event of an acci-
dent.
(3) When sliding or reclining the seat
rearward, pay careful attention to
the rear seat passengers.
G21B024a
To adjust forward or backwardEG21B - Ia
Lift the seat adjusting lever and adjust the
seat forward or backward to the desired
position. After adjustment, release the ad-
justing lever to lock the seat in position.
WARNING
To e n s u r e the seat is locked securely,
attempt to move the seat forward or
backward without using the lever.
G21C027a
To recline the seatbackEG21C-Jf
Adjust the seatback angle by turning the dial.
1-To move to forward direction
2-To recline rearward

SEATS AND SEATBELTS
3–15
CAUTION
(1) Any installation of audio equip-
ment or repairs in the vicinity of
the pre–tensioner seat belts or
floor console must be performed
by an authorized MITSUBISHI
dealer. It is important to do so be-
cause the work could affect the
pre–tensioner mechanisms.
(2) If you need to scrap the vehicle,
please consult an authorized
MITSUBISHI dealer. It is important
to do so because unexpected ac-
tivation of the pre–tensioner seat
belts could cause injuries.
NOTE
(1) The pre–tensioner seat belts will be acti-
vated if the vehicle suffers a severe
frontal impact, even if the seat belts are
not worn.
(2) The pre–tensioner seat belts are de-
signed to work only once. After the pre–
tensioner seat belts have been acti-
vated, they must be replaced by an
authorized MITSUBISHI dealer.
Warning lampThe same warning lamp is shared by the
SRS air bags and the pre–tensioner seat
belts.
Refer to the ”SRS warning lamp” on page
3–36.
Force–limiter mechanismsIn the event of a collision, each force–limiter
mechanism will effectively absorb the load
applied to the seat belt so as to minimize the
impact to the passenger.
Child restraintEG20A-Bb
When transporting children in your vehicle,
some type of child restraint system should
always be used according to the size of the
child. This is required by law in most
countries.
The regulations concerning driving with
children in the front seat may differ from
country to country. You are advised to com-
ply with the relevant regulations.
WARNING
(1) When possible, put children in
the rear seat. Accident statistics
indicate that children of all sizes
and ages are safer when properly
restrained in the rear seat rather
than in the front seat.
(2) Holding a child in your arms is no
substitute for a restraint system.
Failure to use a proper restraint
system can result in severe or
fatal injury to your child.
(3) Each restraint device or fixing is
to be used only by one child.

SEATS AND SEATBELTS
3–16
G28G290a
Caution for installing the child
restraint on vehicle with front
passenger air bag
The label shown here is attached on ve-
hicles with front passenger air bag.
If this label is attached, never install the rear-
facing child restraint on the front passenger’s
seat.
G28G436a
WARNING
(1) Extreme Hazard !
REAR-FACING CHILD RE-
STRAINTS must NOT be used in
the front passenger seat as it
places an infant too close to the
passenger air bag. The force of an
inflating air bag could kill or
cause serious injuries to the
child. Rear-facing child restraints
must only be used in the rear
seat.
G28G439a
WARNING
(2) FRONT-FACING CHILD
RESTRAINTS should be used in
the rear seat whenever possible;
if used in the front seat, adjust the
seat to the fully backward posi-
tion. Failure to do so could kill or
cause serious injuries to the
child.

SEATS AND SEATBELTS
3–17
G28B005a
Infants and small childrenEG20B-Ba
When transporting infants and small children
in your vehicle, follow the instruction given
below.
Instruction:
(1) For small infants, an infant carrier
should be used. For small children
whose height when seated allows the
shoulder belt to lie in contact with the
face or the throat, a child seat should be
used.
(2) The child restraint system should be ap-
propriate for your child’s weight and
height and properly fit the vehicle. For a
higher degree of safety: THE CHILD
RESTRAINT SYSTEM SHOULD BE
INSTALLED IN THE REAR SEAT.(3) Before purchasing a child seat or infant
carrier, first try to install it in the rear seat
to ensure it fits well. Due to the location
of the seat belt buckles in the seat
cushion, it may be difficult to securely in-
stall some child restraint systems.
If the child restraint system can be
pulled forward easily on the seat
cushion after the belt has been tigh-
tened, choose another child restraint
system.
WARNING
(1) When installing a child restraint
system, refer to the instructions
provided by the manufacturer of
the restraint system. Failure to do
so can result in severe or fatal in-
jury to your child.
(2) After installation, push and pull
the child restraint system back
and forth, and side to side, to see
that it is positively secured. If the
child restraint system is not in-
stalled securely, it may cause in-
jury to the child or other occu-
pants in case of accident or
sudden stops.
(3) When the child restraint system is
not in use, keep your child or in-
fant seat secured with the seat
belt or remove it from the vehicle
in order to prevent injury to your
child.

SEATS AND SEATBELTS
3–18
Suitability for various seating positionsEG20CMDa
Seating position
Mass GroupFront PassengerRear PassengerFront PassengerRear OutboardRear Centre
0–Up to 10 kg (0 – 9 months)XU,L*1X
0+ – Up to 13 kg (0 – 2 years)XUX
I – 9 to 18 kg (9 months – 4 years)L*2U,L*2L*2
II & III – 15 to 36 kg (4 – 12 years)L*3U,L*3L*3
Key of letters inserted in the above table:U – Suitable for “universal” category restraints approved for use in this mass group.
UF – Suitable for forward–facing “universal” category restraints approved for use in this mass group.
L – Suitable for particular child restraints (MITSUBISHI genuine parts).
B – Built–in restraint approved for this mass group.
X – Seat position not suitable for children in this mass group.
L (Genuine part information)
Genuine parts No.ECE No.
*1MZ311097E1–03301063
*2MZ312389E1–03301085
*3MZ311099E1–03301061
NOTE
There is no applicable MITSUBISHI Genuine Parts to the Mass Group “0+–Up to 13 kg (0–2 years)”.
MITSUBISHI MOTOR SALES Europe B.V. reserves the right to changes without any prior announcement.
For detail information, please consult your authorized MITSUBISHI dealer.

SEATS AND SEATBELTS
3–19
G18C021a
Installing a child restraint system
to a 3-point type seat belt
(with emergency/automatic lock-
ing mechanism)
EG20D-A
The 3-point type seat belts at the seat posi-
tions above can be converted from normal
emergency locking retractor (ELR) mode to
automatic locking retractor (ALR) mode. It
must be so converted, when installing a child
restraint system.
G18C054a
Installation:
1. Place the child restraint system in the
rear seating position as shown in the
illustration.
2. Route the belt through the child re-
straint according to the child restraint
system manufacturer’s instructions,
then insert the latch plate into the
buckle.
G18C055a
3. To activate the ALR mode, slowly pull
the shoulder part of the belt all the way
out until it stops, then let the belt feed
back into the retractor.
4. After the belt has retracted, tug on it. If
the belt is locked, you will not be able
to pull it out. If you can pull the belt out,
it is not locked and you will need to re-
peat these steps.

SEATS AND SEATBELTS
3–20
G18C056a
5. After confirming that the belt is locked,
grab the shoulder part of the belt near
the buckle and pull up to remove any
slack from the lap part of the belt. Re-
member, if the lap part of the belt is not
tight, the child restraint will not be se-
cure. It may help to put weight on the
child restraint or to push on the seat-
back while pulling up on the belt.
6. Before putting the child in the restraint,
push and pull the restraint in all direc-
tions to be sure it is secure. Do this be-
fore each use.
7. To deactivate the ALR mode in order
to remove a child restraint etc., after
removing the child from the restraint,
unlatch the buckle, unroute the seat
belt, let the belt fully retract and rewind
the belt.NOTE
If the seat belt does not lock, rewind it fully,
then perform step 2 to 7 again.
WARNING
(1) Before putting the child in the re-
straint, be absolutely sure to
make the conversion of the re-
tractor from the ELR mode to the
ALR mode. By doing so, the child
restraint system is always tightly
secured to the seat by the auto-
matic lock. If the conversion to
ALR is not made, the child re-
straint system could move for-
ward in the event of sudden brak-
ing or an accident, seriously in-
juring the child or other occu-
pants.
(2) If a person wearing the seat belt
moves one’s upper body signifi-
cantly such that the belt com-
pletely unwinds, the retractor
may switch to its ALR mode and
lock, thus preventing further
movement. If this happens, the
person should switch the retrac-
tor back to its ELR mode by tak-
ing off the seat belt and fully re-
winding it. The person should
then wear the seat belt again.
G18C023a
Installing a child restraint system
to a 3–point type seat belt (with
emergency locking mechanism)
EG20E–Aa
For safety, you are advised to install the
child restraint system using a 3–point type
seat belt with emergency/automatic lock-
ing mechanism. If you cannot avoid instal-
ling it using another type of seat belt, follow
the instructions given below.
Installation:
1. Fasten the seat belt to secure the child
restraint system. Make sure you hear
a ”click” when you insert the latch plate
in the buckle.
2. 3–point type seat belts require no
length adjustment. Remove all slack
by using the locking clip.
3. Push and pull the child restraint in all
directions to be sure it is secure.

SEATS AND SEATBELTS
3–21
G28B059a
CAUTION
For some type of child restraint, the
locking clip (A) should be used to
help avoid personal injury during a
collision or sudden manoeuvre.
It must be fitted and used in accor-
dance with the child restraint
manufacturer’s instructions.
The locking clip must be removed
when the child restraint is removed.
Older childrenEG20F-Aa
Children who have outgrown the child re-
straint system should be seated in the rear
seat and wear a combination lap shoulder
belt.
The lap belt should be snug and positioned
low on the abdomen so that it is below the
top of the hip-bone. Otherwise, the belt could
intrude into the child’s abdomen during an
accident and cause injury.
CAUTION
(1) Children who are not buckled up
can be thrown out of the vehicle
in an accident.
(2) Children who are not buckled up
can strike other people.
(3) A child should never be left unat-
tended in your vehicle. When you
leave the vehicle, take the
children with you.
Pregnant women restraintEG28C - C
WARNING
MITSUBISHI MOTOR SALES Europe
B.V. recommends that pregnant
women use the available seat belts.
This will reduce the likelihood of in-
jury to both the woman and the un-
born child. The lap belt should be
worn across the thighs and as snug
against the hips as possible, but not
across the waist. The woman’s doctor
should be consulted if there are any
questions.
Seat belt inspectionEG28D-E
(1) Check the belts for cuts, worn or frayed
webbing and for cracked or deformed
metallic parts. Replace the belt assem-
bly if defective.
(2) A dirty belt should be cleaned with neu-
tral detergent in warm water. After rins-
ing in water, let it dry in the shade. Do not
attempt to bleach or re-dye the belts be-
cause this affects their characteristics.